HUB
Networks using a Star topology require a central point for the devices to connect. Originally this device was called a concentrator since it consolidated the cable runs from all network devices. The basic form of concentrator is the hub.
As shown in Figure; the hub is a hardware device that contains multiple, independent ports that match the cable type of the network. Most common hubs interconnect Category 3 or 5 twisted-pair cable with RJ-45 ends, although Coax BNC and Fiber Optic BNC hubs also exist. The hub is considered the least common denominator in device concentrators. Hubs offer an inexpensive option for transporting data between devices, but hubs don't offer any form of intelligence. Hubs can be active or passive.
An active hub strengthens and regenerates the incoming signals before sending the data on to its destination.
Passive hubs do nothing with the signal.
Ethernet Hubs
An Ethernet hub is also called a multiport repeater. A repeater is a device that amplifies a signal as it passes through it, to counteract the effects of attenuation. If, for example, you have a thin Ethernet network with a cable segment longer than the prescribed maximum of 185 meters, you can install a repeater at some point in the segment to strengthen the signals and increase the maximum segment length. This type of repeater only has two BNC connectors, and is rarely seen these days.
8 Port mini Ethernet Hub
The hubs used on UTP Ethernet networks are repeaters as well, but they can have many RJ45 ports instead of just two BNC connectors. When data enters the hub through any of its ports, the hub amplifies the signal and transmits it out through all of the other ports. This enables a star network to have a shared medium, even though each computer has its own separate cable. The hub relays every packet transmitted by any computer on the network to all of the other computers, and also amplifies the signals.
The maximum segment length for a UTP cable on an Ethernet network is 100 meters. A segment is defined as the distance between two communicating computers. However, because the hub also functions as a repeater, each of the cables connecting a computer to a hub port can be up to 100 meters long, allowing a segment length of up to 200 meters when one hub is inserted in the network.
Multistation Access Unit
A Multistation Access Unit (MAU) is a special type of hub used for token ring networks. The word "hub" is used most often in relation to Ethernet networks, and MAU only refers to token ring networks. On the outside, the MAU looks like a hub. It connects to multiple network devices, each with a separate cable.
Unlike a hub that uses a logical bus topology over a physical star, the MAU uses a logical ring topology over a physical star.
When the MAU detects a problem with a connection, the ring will beacon. Because it uses a physical star topology, the MAU can easily detect which port the problem exists on and close the port, or "wrap" it. The MAU does actively regenerate signals as it transmits data around the ring.
Switches
Switches are a special type of hub that offers an additional layer of intelligence to basic, physical-layer repeater hubs. A switch must be able to read the MAC address of each frame it receives. This information allows switches to repeat incoming data frames only to the computer or computers to which a frame is addressed. This speeds up the network and reduces congestion.
Switches operate at both the physical layer and the data link layer of the OSI Model.
Bridges
A bridge is used to join two network segments together, it allows computers on either segment to access resources on the other. They can also be used to divide large networks into smaller segments. Bridges have all the features of repeaters, but can have more nodes, and since the network is divided, there is fewer computers competing for resources on each segment thus improving network performance.
Bridges can also connect networks that run at different speeds, different topologies, or different protocols. But they cannot, join an Ethernet segment with a Token Ring segment, because these use different networking standards. Bridges operate at both the Physical Layer and the MAC sublayer of the Data Link layer. Bridges read the MAC header of each frame to determine on which side of the bridge the destination device is located, the bridge then repeats the transmission to the segment where the device is located.
Routers
Routers Are networking devices used to extend or segment networks by forwarding packets from one logical network to another. Routers are most often used in large internetworks that use the TCP/IP protocol suite and for connecting TCP/IP hosts and local area networks (LANs) to the Internet using dedicated leased lines.
Routers work at the network layer (layer 3) of the Open Systems Interconnection (OSI) reference model for networking to move packets between networks using their logical addresses (which, in the case of TCP/IP, are the IP addresses of destination hosts on the network). Because routers operate at a higher OSI level than bridges do, they have better packet-routing and filtering capabilities and greater processing power, which results in routers costing more than bridges.
Routing tables
Routers contain internal tables of information called routing tables that keep track of all known network addresses and possible paths throughout the internetwork, along with cost of reaching each network. Routers route packets based on the available paths and their costs, thus taking advantage of redundant paths that can exist in a mesh topology network.
Because routers use destination network addresses of packets, they work only if the configured network protocol is a routable protocol such as TCP/IP or IPX/SPX. This is different from bridges, which are protocol independent. The routing tables are the heart of a router; without them, there's no way for the router to know where to send the packets it receives.
Unlike bridges and switches, routers cannot compile routing tables from the information in the data packets they process. This is because the routing table contains more detailed information than is found in a data packet, and also because the router needs the information in the table to process the first packets it receives after being activated. A router can't forward a packet to all possible destinations in the way that a bridge can.
- Static routers: These must have their routing tables configured manually with all network addresses and paths in the internetwork.
- Dynamic routers: These automatically create their routing tables by listening to network traffic.
- Routing tables are the means by which a router selects the fastest or nearest path to the next "hop" on the way to a data packet's final destination. This process is done through the use of routing metrics.
- Routing metrics which are the means of determining how much distance or time a packet will require to reach the final destination. Routing metrics are provided in different forms.
- hop is simply a router that the packet must travel through.
- Ticks measure the time it takes to traverse a link. Each tick is 1/18 of a second. When the router selects a route based on tick and hop metrics, it chooses the one with the lowest number of ticks first.
You can use routers, to segment a large network, and to connect local area segments to a single network backbone that uses a different physical layer and data link layer standard. They can also be used to connect LAN's to a WAN's.
ROUTING PROTOCOLS
ROUTING PROTOCOLS are the software that allow routers to dynamically advertise and learn routes, determine which routes are available and which are the most efficient routes to a destination.
Routing protocols used by the Internet Protocol suite include:
- Routing Information Protocol (RIP and RIP II)
- Open Shortest Path First (OSPF)
- Intermediate System to Intermediate System (IS-IS)
- Interior Gateway Routing Protocol (IGRP)
- Cisco's Enhanced Interior Gateway Routing Protocol (EIGRP)
- Border Gateway Protocol (BGP)
Routing is the process of moving data from one network to another network. Within a network, all hosts are directly accessable and do not need to pass data through a default gateway. All hosts on the same network are directly connected and can communicate directly with each other.
ROUTED PROTOCOLS
ROUTED PROTOCOLS are nothing more than data being transported across the networks. Routed protocols include:
- Internet Protocol
- Novell IPX
- Open Standards Institute networking protocol
- DECnet
- Appletalk
- Banyan Vines
- Xerox Network System (XNS)
Outside a network, specialized devices called ROUTERS are used to perform the routing process of forwarding packets between networks. Routers are connected to the edges of two or more networks to provide connectivity between them. These devices are usually dedicated machines with specialized hardware and software to speed up the routing process. These devices send and receive routing information to each other about networks that they can and cannot reach. Routers examine all routes to a destination, determine which routes have the best metric, and insert one or more routes into the IP routing table on the router. By maintaining a current list of known routes, routers can quicky and efficiently send your information on it's way when received.
There are many companies that produce routers: Cisco, Juniper, Bay, Nortel, 3Com, Cabletron, etc. Each company's product is different in how it is configured, but most will interoperate so long as they share common physical and data link layer protocols (Cisco HDLC or PPP over serial, Ethernet etc.). Before purchasing a router for your business, always check with your Internet provider to see what equipment they use, and choose a router which will interoperate with your Internet provider's equipment.
NON-ROUTABLE PROTOCOLS
- NetBEUI
- DLC
- LAT
- DRP
- MOP
Brouters
Brouters are a combination of router and bridge. This is a special type of equipment used for networks that can be either bridged or routed, based on the protocols being forwarded. Brouters are complex, fairly expensive pieces of equipment and as such are rarely used.
A Brouter transmits two types of traffic at the exact same time: bridged traffic and routed traffic. For bridged traffic, the Brouter handles the traffic the same way a bridge or switch would, forwarding data based on the physical address of the packet. This makes the bridged traffic fairly fast, but slower than if it were sent directly through a bridge because the Brouter has to determine whether the data packet should be bridged or routed.
No comments:
Post a Comment